Echo W1 Cycle Computer Manual Download

[. . . ] When riding is stopped, the speed will continue to count 4 seconds for Bike 1 and count 2 seconds for Bike2 to confirm that no more wheel signals have been sent. 10. 00 ­ 990. 00 Km or Mile +/- 0. 1% ODO: Odometer 0. 0 ­ 99999. 9 Km or Miles +/- 0. 1% B. Attach the bracket to the handlebar and fit the rubber pad between the handlebar and the band of the bracket. Slide the main unit onto the bracket from front to rear till it clicks into position. To remove the main unit, press down on the lock lever of the bracket then pull the main unit forward and off. [. . . ] The T-TM accumulates total riding time from the beginning of computer use and can not be cleared by the RESET operation. It will automatically begin counting upon riding, and continue to count 4 seconds for Bike1 and 2 seconds for Bike2 to confirm that no more wheel sensing signals have been sent when riding is stopped. But this computer revises back the over-counted 2 or 4 seconds automatically. * : 12HR AM/PM or 24HR Clock 0. 003% AV: Average Speed 0:00'00' ­ 12:59'59' AM/PM or 23:59'59' 0. 0 ­ 199. 9 Km/h / 0. 0 ­ 120. 0Mile/h +/- It can display the current time in 12HR AM/PM or 24HR clock. +/- 0. 1% 1. It displays '0. 0' when TM is less than 4 sec. , and is updated by about one second when TM is over 4 seconds. It displays an 'Err' symbol when either the TM is over 100 hours or the DS is over 1, 000km (or miles). Reset the unit in order to restart. All descriptions are similar as the Lubrication Reminder except the word of Maintenance instead of Lubrication and the symbol ' ' shall be replaced by the symbol ' '. Sensor with Transmitter: No Contact Magnet sensor with Wireless Transmitter. Suitable Fork Size: 12mm to 50mm& (0. 5' to 2. 0' &) Forks. Wireless Sensing Distance: 55cm (1. 8 feet) between the transmitter and the main unit. Cross-Talking Interference: Within 40 cm (15. 8'), no interference by 2 bicycles carrying similar cycle computers, even when ridden side by side. Wheel Circumference Setting: 1mm - 3999mm (1mm increment) Operation Temperature: 0°C ~ 50°C (32°F ~ 122°F) Storage Temperature: - 10°C ~ 60°C (14°F ~ 140°F) Main Unit Battery Power: 3V battery x 1 (CR2032), battery operating life is about 2 years. (Based on an average of 1. 5 hours use per day) Transmitter Battery Power: 1. 5V battery x 1 (typical LR44). About 24, 000km/15, 000 miles riding distance or 2 years battery operating life. (The original factory-attached battery life may be shorter than this period due to shipping and storage time). Dimensions and Weight Main Unit: 44. 0 x 53. 0 x 19. 3mm/31. 5g Transmitter: 20. 0mm& x 48. 0mm/14. 1g DS: Trip Distance 0. 00 ­ 999. 99 Km or Miles +/- 0. 1% The DS function accumulates the distance data from the last RESET operation as long as the bike is being ridden. * The specifications and designs may be changed without notice. I NDEX: MEANS PRESS BUTTON N MORE THAN 2 SECONDS. } p LUBRICATION or MAINTENANCE REMINDER SETTING (For W2 only) p BIKE 1 or BIKE 2 SELECTION (For W2 only) (Fig. The patent-pending transmitter circuit is designed to reduce power consumption; a 1. 5V battery (typically an LR44) can operate for over 24, 000km (15, 000miles) riding distance or 2 years. Replace a new battery when the transmitter's battery power is nearly exhausted, otherwise the transmission power of the wheel signal will be weak, causing the main unit to display unstable data. Replace with a new LR44 battery 16 with the positive (+) pole toward the sensor cap 10 . Hold down the MODE button and SET button simultaneously for more than 3 seconds to initiate the computer and clear all data. IMPORTANT: Be sure to initiate the computer before it is be used, otherwise the computer may run errors. The LCD segments will be tested automatically after the unit is initiated. The user's friendly function is to remind you about lubricating or maintaining your beloved bike after presetting the desired reminding distance. [. . . ] N): Get a suitable circumference value from the table. AUTOMATIC START/STOP & POWER AUTO ON/OFF The computer will automatically begin counting data upon riding and stop counting data when riding is stopped. The flickering symbol ' ' indicates that the computer is at start status. To preserve battery, this computer will automatically switch off and just displays the ' ' data when it has not been used for about 30 minutes. The symbol ' ' will appear to indicate the battery is nearly exhausted. [. . . ]

The symbol ofp means this function is for ECHO-W2 only; all descriptions with this symbol

A. PHYSICAL DESCRIPTIONS

1. LCD DISPLAY 2. MODE BUTTON 3. MAIN BATTERY CAP

4. SET BUTTON 5. SILDE ON/OFF SWITCH6. RUBBER PAD

7. BRACKET 8. SENSOR MARKING LINE 9. SENSOR (TRANSMITTER)

10. SENSOR BATTERY CAP11. SENSOR BAND 12. BAND CARRIER

16.1.5VBATTERY(LR44ISTYPICAL) 17.SCREW 18.NUT

BRACKET AND MAIN UNIT MOUNTING

1. Attach the bracket i to the handlebar and fit the rubber pad h between the handlebar and the band of

the bracket. Tighten the screw securely till the bracket cannot turn. (Fig. A)

2. Slide the main unit onto the bracket from front to rear till it clicks into position. To remove the main unit,

press down on the lock lever of the bracket then pull the main unit forward and off. (Fig. B)

SENSOR AND MAGNET MOUNTING

11

17

2. Mount the band carrier

12

3. Mounting the sensor unit on the right front fork with rubber pad. (Fig. D)

13

5.Adjust the relative position between the main unit and the sensor, according to the following key points:

a). It will receive a stronger wireless signal if the sensor is more close to the main unit.

as possible and within 45 cm (1.5 feet) to get a better wireless performance. (Fig. F)

It is workable when the arrow symbol is down (Fig. E), but keeping the arrow up is better because its

sensing distance is shorter than with the arrow down.

b). Adjust the installation angle of the sensor to aim at the direction of the main unit within +/- 15°, the

best performances is at vertical direction (90°) between the sensor’s arrow and the battery cap of the

c).

6. Refer to the TEST section to testing the installation before tighten the sensor band with ascrewdriver.(Fig. I)

. (Fig. J)

TEST

1. The main unit has a 'Slide On/Off Detecting Switch g' (patents pending) to turn ON/OFF the power of

the wireless receiver. It can receive the wireless wheel signal only after the main unit is slid onto the

2. Spin the front wheel to check if installation is correct. Installation is correct if the main unit flickers '

symbol. It is an incorrect installation if there is no symbol of '

among the main unit, the sensor and the magnet, or refer to the trouble-shooting table.

C. THE WIRELESS SYSTEM AND PERFORMANCES

1. The sensor transits the wheel rotating signal to the receiver in the main unit by the wireless transmission.

To prevent the receiver from interfering by other wireless noises and causing the main unit to display false

data, install the transmitter according to the following key points to get better performance.

interference from other sources. Adjust the installation angle of transmitter to aim at the direction to

the main unit within a +/- 15° angle, the best performance is at a vertical direction.

stronger sensing signal not only has better noise immunity, but also increases the transmitter battery’s

operating life. For good wireless performance, please install the transmitter as close to the main unit

2. Precaution

a). This computer has almost no cross-talking interference when 2 bicycles carrying the same or similar

wireless cycle computers are ridden side by side, as long as the cross-distance is over 40cm (15.8”).

b). This computer has excellent noise immunity for some electromagnetic interference, but it may be interfered

with by a strong electromagnetic wave and make the main unit displays error data while it is near strong

interference such as TV transmission stations, radar stations, and some heavy industrial machines.

3. This computer has a “Slide On/Off Detecting Switch”

g to check the main unit to slide on/off from the bracket.

a). To reduce the power consumption of the main unit to increase the battery operation life, but also to

delete all indoor electromagnetic interference from electrical equipment (such as PC monitors,

handy-phones, etc.). It will turn off the power supply of the receiver when the main unit takes off from the

b). The main unit can only receive the wheel signal after it is slid onto the bracket.

: Current Speed 0.0 – 199.9 Km/h or 120.0 Mile/h +/- 1% (Typical)

1. The current speed is always displayed on the upper display when riding. It displays current speed up to

199.9 KM/h or 120.0 M/h (for wheel diameters of over 24 inches).

Bike2 to confirm that no more wheel signals have been sent.

1. The odometer cumulates the total distance as long as the bike is running.

DO data can not be cleared to zero by RESET operation.

ODO1, ODO2 and T

ODO: Bike1, Bike 2 and Total Odometer (For W2 only)

1. The odometer cumulates the total distance as long as the bike is running, either Bike 1 or 2 has its

DO 1 or ODO 2 individually. The T

ODO is the sum of the ODO 1 plus ODO 2.

-

ODO data can not be cleared to zero by RESET operation.

TM: Riding Time 0M00.0S-59M59.9S, 1H00M00S-99H59M59S +/- 0.003%

-

1. The TM totals the riding time from the last RESET operation. The T-TM accumulates total riding time

from the beginning of computer use and can not be cleared by the RESET operation.

seconds for Bike2 to confirm that no more wheel sensing signals have been sent when riding is stopped.

But this computer revises back the over-counted 2 or 4 seconds automatically.

AV: Average Speed 0.0 – 199.9 Km/h / 0.0 – 120.0Mile/h +/- 0.1%

1. It is calculated from the DS divided by the TM. The average data counted is from the last RESET to

2. It displays '0.0' when T

M is less than 4 sec., and is updated by about one second when TM is over 4 seconds.

M is over 100 hours or the DS is over 1,000km (or miles).

DS:TripDistance 0.00–999.99KmorMiles +/-0.1%

The DS function accumulates the distance data from the last RESET operation as long as the bike is being

1. This user-friendly function is created by ECHOWELL and patents are pending worldwide. It will remind

you to lubricate your beloved bike after you preset the reminder.

2. The preset distance will be counted down, the LCD will flash the '' symbol when the preset

distance will count down to 0 to remind you to lubricate your bike.

3. The reminding distance will count up after counting down to zero and the 'o' symbol will display on the

left of distance to indicate the distance is over the lubrication reminding distance if you did not reset

' shall be replaced by the symbol ''.

Remarks: All functions’ data are updated about one second.

or 2 years battery operating life. (The original factory-attached battery

life may be shorter than this period due to shipping and storage time).

*

The specifications and designs may be changed without notice.